Perkins 1206E-E66TA Engine Disassembly Assembly Shop Manual

$19.99

Category:

 High definition, searchable, printable PDF  Instant download

Covers: Perkins 1206E-E66TA Industrial Engine Disassembly and Assembly. Serial numbers:

  • BK (Engine)

PN: KENR9115 (July 2011)
Pages
: 236
Format:
PDF

The following is a list of topics contained in the Perkins Shop Manual:

Disassembly and Assembly Section
Fuel Priming Pump – Remove and Install (Mechanical Priming Pump)
Flow Control Valve – Remove and Install
Fuel Filter Base – Remove and Install (Twin Secondary Fuel Filter)
Water Separator and Fuel Filter (Primary) – Remove and Install
Fuel Manifold (Rail) – Remove and Install
Fuel Injection Lines – Remove
Fuel Injection Lines – Install
Exhaust Cooler (NRS) – Remove
Exhaust Cooler (NRS) – Install
Inlet Air Control – Remove (NRS Inlet Air Mixer)
Inlet Air Control – Install (NRS Inlet Air Mixer)
Fuel Injection Pump – Remove
Fuel Injection Pump – Install
Fuel Injection Pump Gear – Remove
Fuel Injection Pump Gear – Install
Electronic Unit Injector – Remove
Electronic Unit Injector – Install
Wastegate Solenoid – Remove and Install
Exhaust Back Pressure Valve – Remove and Install
Flexible Exhaust Pipe – Remove and Install
Exhaust Manifold and Turbocharger – Remove
Exhaust Manifold and Turbocharger – Install
Exhaust Elbow – Remove and Install
Diesel Particulate Filter – Remove
Diesel Particulate Filter – Install
Inlet and Exhaust Valve Springs – Remove and Install
Inlet and Exhaust Valves – Remove and Install
Engine Oil Filter Base – Remove and Install
Engine Oil Cooler – Remove (Engine Oil Cooler with a Low Mounted Filter Base)
Engine Oil Cooler – Remove (Engine Oil Cooler with a High Mounted Filter Base)
Engine Oil Cooler – Install (Engine Oil Cooler with a Low Mounted Filter Base)
Engine Oil Cooler – Install (Engine Oil Cooler with a High Mounted Filter Base)
Engine Oil Pump – Remove
Engine Oil Pump – Install
Water Pump – Remove
Water Pump – Install
Water Temperature Regulator – Remove and Install

Flywheel – Remove
Flywheel – Remove (Equipped with Rear Power Take-Off)
Flywheel – Install
Flywheel – Install (Equipped with Rear Power Take-Off)
Crankshaft Rear Seal – Remove
Crankshaft Rear Seal – Install
Flywheel Housing – Remove and Install (Wet Back End Housing)
Flywheel Housing – Remove and Install (Standard Housing)
Vibration Damper and Pulley – Remove
Vibration Damper and Pulley – Install
Crankshaft Front Seal – Remove and Install
Crankshaft Front Seal – Remove and Install
(Crankshaft Front Seal for Heavy Duty Front
Cover)
Front Cover – Remove and Install (Heavy Duty Front
Cover)
Front Cover – Remove and Install
Gear Group (Front) – Remove and Install
Gear Group (Front) – Remove and Install (Heavy
Duty Gear Group (Front))
Idler Gear – Remove
Idler Gear – Install
Housing (Front) – Remove
Housing (Front) – Remove (Heavy Duty Housing
(Front))
Housing (Front) – Install
Housing (Front) – Install (Heavy Duty Housing
(Front))
Accessory Drive – Remove and Install (Accessory
Drive SAE “B”)
Accessory Drive – Remove and Install (Accessory
Drive SAE “A”)
Crankcase Breather – Remove
Crankcase Breather – Install
Valve Mechanism Cover – Remove and Install
Rocker Shaft and Pushrod – Remove
Rocker Shaft – Disassemble
Rocker Shaft – Assemble
Rocker Shaft and Pushrod – Install
Cylinder Head – Remove
Cylinder Head – Install
Lifter Group – Remove and Install (Hydraulic Lifter
Group)
Camshaft – Remove and Install
Camshaft Gear – Remove and Install
Camshaft Bearings – Remove and Install
Engine Oil Pan – Remove (Aluminum Oil Pan)
Engine Oil Pan – Install (Aluminum Oil Pan)
Engine Oil Pan Plate – Remove and Install (Aluminum
Oil Pan)
Piston Cooling Jets – Remove and Install
Pistons and Connecting Rods – Remove
Pistons and Connecting Rods – Disassemble
Pistons and Connecting Rods – Assemble
Pistons and Connecting Rods – Install
Connecting Rod Bearings – Remove (Connecting
Rods in Position)
Connecting Rod Bearings – Install (Connecting Rods
in Position)
Crankshaft Main Bearings – Remove and Install
(Crankshaft in position)
Crankshaft – Remove
Crankshaft – Install
Crankshaft Timing Ring – Remove and Install
Crankshaft Gear – Remove and Install
Bearing Clearance – Check
Refrigerant Compressor – Remove and Install
Atmospheric Pressure Sensor – Remove and
Install
Camshaft Position Sensor – Remove and Install
Crankshaft Position Sensor – Remove and
Install
Coolant Temperature Sensor – Remove and
Install
Engine Oil Pressure Sensor – Remove and Install

Soot Antenna – Remove and Install
Temperature Sensor (DPF) – Remove and
Install
Pressure Sensor (DPF) – Remove and Install (Clean
Emissions Module)
Temperature Sensor (Cooled Exhaust Gas) – Remove
and Install
Pressure Sensor (Cooled Exhaust Gas) – Remove
and Install (NRS Inlet and Outlet Pressure
Sensors)
Boost Pressure Sensor – Remove and Install
Inlet Manifold Temperature Sensor – Remove and
Install
Glow Plugs – Remove and Install
Alternator Belt – Remove and Install
Idler Pulley – Remove and Install (Grooved Idler
Pulley)
Belt Tensioner – Remove and Install
Belt Tensioner – Remove and Install
Fan – Remove and Install
Fan Drive – Remove and Install
Electronic Control Module – Remove and Install
(Electronic Control Module With Banjo Bolt
Connections)
Electronic Control Module – Remove and Install
(Electronic Control Module With Quick Coupler
Connections)
ECM Mounting Bracket – Remove and Install
Alternator – Remove
Electric Starting Motor – Remove and Install
Alternator – Install
Air Compressor – Remove and Install (Twin Cylinder
Compressor)
Index Section
Index

Contains Specifications, Illustrations and Procedures

Reviews

There are no reviews yet.

Be the first to review “Perkins 1206E-E66TA Engine Disassembly Assembly Shop Manual”

Your email address will not be published. Required fields are marked *