Perkins 1106C Genset Disassembly & Assembly Shop Manual

$19.99

Category:

 High definition, searchable, printable PDF  Instant download

Covers: Perkins 1106C Genset Disassembly and Assembly

  • PK (Engine)

Pages: 192
Format:
PDF
Compatibility: Windows/Mac/Tablet

The following is a list of topics contained in the Shop Manual:

Disassembly and Assembly Section
Fuel Priming Pump – Remove and Install (Mechanical Priming Pump)
Fuel Priming Pump – Remove and Install (Electrical Priming Pump)
Fuel Filter Base – Remove and Install (Secondary Fuel Filter)
Fuel Transfer Pump – Remove
Fuel Transfer Pump – Install
Fuel Manifold (Rail) – Remove and Install
Fuel Injection Lines – Remove
Fuel Injection Lines – Install
Fuel Injection Pump – Remove
Fuel Injection Pump – Install
Fuel Injection Pump Gear – Remove
Fuel Injection Pump Gear – Install
Electronic Unit Injector – Remove
Electronic Unit Injector – Install
Turbocharger – Remove (Turbocharger Top Mounted
)
Turbocharger – Remove (Side Mounted
Turbocharger)
Turbocharger – Disassemble
Turbocharger – Assemble
Turbocharger – Install (Turbocharger Top
Mounted)
Turbocharger – Install (Side Mounted
Turbocharger)
Wastegate Solenoid – Remove and Install
Exhaust Manifold – Remove and Install (Side
Mounted Exhaust Manifold)
Exhaust Manifold – Remove and Install (Top Mounted
Exhaust Manifold)
Exhaust Elbow – Remove and Install
Inlet Manifold – Remove and Install
Inlet and Exhaust Valve Springs – Remove and
Install
Inlet and Exhaust Valves – Remove and Install
Engine Oil Filter Base – Remove and Install
Engine Oil Cooler – Remove (Engine Oil Cooler with
a Low Mounted Filter Base)
Engine Oil Cooler – Remove (Engine Oil Cooler with
a High Mounted Filter Base)
Engine Oil Cooler – Install (Engine Oil Cooler with a
Low Mounted Filter Base)
Engine Oil Cooler – Install (Engine Oil Cooler with a
High Mounted Filter Base)
Engine Oil Relief Valve – Remove and Install
Engine Oil Pump – Remove
Engine Oil Pump – Install
Water Pump – Remove
Water Pump – Install
Water Temperature Regulator – Remove and Install

Flywheel – Remove
Flywheel – Install
Crankshaft Rear Seal – Remove
Crankshaft Rear Seal – Install
Flywheel Housing – Remove and Install (Standard
Housing)
Flywheel Housing – Remove and Install (Wet Back
End Housing)
Vibration Damper and Pulley – Remove (Pulleys
without Split Lock Rings)
Vibration Damper and Pulley – Remove (Pulley with
Split Lock Rings)
Vibration Damper and Pulley – Install (Pulleys without
Split Lock Rings)
Vibration Damper and Pulley – Install (Pulley with
Split Lock Rings)
Crankshaft Front Seal – Remove and Install
Front Cover – Remove and Install
Gear Group (Front) – Remove and Install
Idler Gear – Remove
Idler Gear – Install
Housing (Front) – Remove
Housing (Front) – Install
Accessory Drive – Remove and Install
Crankcase Breather – Remove (Unfiltered
Breather)
Crankcase Breather – Remove (Filtered
Breather)
Crankcase Breather – Install (Unfiltered
Breather)
Crankcase Breather – Install (Filtered Breather)
Valve Mechanism Cover – Remove and Install
(Composite Valve Mechanism Cover)
Valve Mechanism Cover – Remove and Install
Valve Mechanism Cover Base – Remove and Install
(Composite Valve Mechanism Cover Base)
Valve Mechanism Cover Base – Remove and
Install
Rocker Shaft and Pushrod – Remove
Rocker Shaft – Disassemble
Rocker Shaft – Assemble
Rocker Shaft and Pushrod – Install
Cylinder Head – Remove
Cylinder Head – Install
Lifter Group – Remove and Install
Camshaft – Remove and Install
Camshaft Gear – Remove and Install
Camshaft Bearings – Remove and Install
Engine Oil Pan – Remove (Aluminum Oil Pan)
Engine Oil Pan – Remove (Cast Iron Oil Pan)
Engine Oil Pan – Install (Cast Iron Oil Pan)
Engine Oil Pan – Install (Aluminum Oil Pan)
Engine Oil Pan Plate – Remove and Install (Aluminum
Oil Pan)
Piston Cooling Jets – Remove and Install
Pistons and Connecting Rods – Remove
Pistons and Connecting Rods – Disassemble
Pistons and Connecting Rods – Assemble
Pistons and Connecting Rods – Install
Connecting Rod Bearings – Remove (Connecting
rods in position)
Connecting Rod Bearings – Install (Connecting rods
in position)
Crankshaft Main Bearings – Remove and Install
(Crankshaft in position)
Crankshaft – Remove
Crankshaft – Install
Crankshaft Timing Ring – Remove and Install
Crankshaft Gear – Remove and Install
Bearing Clearance – Check
Crankshaft Position Sensor – Remove and
Install
Position Sensor (Fuel Injection Pump) – Remove and
Install
Coolant Temperature Sensor – Remove and
Install
Engine Oil Pressure Sensor – Remove and Install

Fuel Pressure Sensor – Remove and Install
Boost Pressure Sensor – Remove and Install
Inlet Air Temperature Sensor – Remove and
Install
Glow Plugs – Remove and Install
Alternator Belt – Remove and Install
Fan – Remove and Install
Fan Drive – Remove and Install
Electronic Control Module – Remove and Install
ECM Mounting Bracket – Remove and Install
Alternator – Remove (Alternators with Mounting
Lugs)
Alternator – Remove (Alternators with Mounting
Pads)
Alternator – Install (Alternators with Mounting
Lugs)
Alternator – Install (Alternators with Mounting
Pads)
Electric Starting Motor – Remove and Install
Air Compressor – Remove and Install
Index Section
Index

Contains  Perkins Specifications, Illustrations and Procedures

Reviews

There are no reviews yet.

Be the first to review “Perkins 1106C Genset Disassembly & Assembly Shop Manual”

Your email address will not be published. Required fields are marked *